North Sea Well Access Restored Through Intelligent Wireline Intervention Well-Safe Solutions Recovers 11,575 ft of Slickline Lost in a Well After 15 Years Collection of data with minimal pressure loss in flowing wells Contingency barrier option on high-value subsea wells Recovery of magnetic junk in high temperature wells Hard scale removal at multiple obstruction points Retrieval of equipment lost in the well and fast-track production restart High deviation, heavy-duty fishing, North Sea Recovery of safety valve lockout tool which had parted downhole Retrieval of sub-surface safety valve (SSSV) with damaged fish neck Retrieval of injection valve backed off from 7-in retrievable bridge plug Trial deployment of slickline-set SIM plugs and Peak latch/seal micro coil stinger Data acquisition to monitor pressure buildup in a shut-in well Bespoke activation tool design Evaluation of an e-line deployed tractor, stroker, and slickline toolstring Trial test to remove hard scale from production tubing using mechanical means Cut wire at rope socket to retrieve stuck toolstring Retrieval of injection valve from tubing crossover at 10,400 ft High-deviation fishing at depth in the Middle East > Isolation of failed inflow valve at high deviation Location and stabilization of a leak path in the completion string Innovative use of an LWIV to perform first subsea slickline intervention in Nigeria Efficient straddle solution enables repair of production Christmas tree Permanent plug keeps P&A project moving Peak eCutter facilitates faster stuck toolstring recovery in long-reach, highly-deviated well Retrievable sand screen anchoring system eliminates leaks Mechanical scale removal saves USD 250,000 PTTEP gas lift straddle conversion restores oil production for mature well Slickline-deployed plug isolates damage to avoid workover KOC restores oil production to 800 bbl/d using digital-slickline-conveyed straddle system D-Set setting tool and DSL digital slickline cable set large-bore gauge hanger in monobore well Retrievable bridge plug enables proper tubing cut and saves 4 rig days, Congo Remote Intervention Operation Enables Effective Planning of Plug and Abandonment Campaign Shell Removes 900-ft Parted Wireline from North Sea Well Setting a Critical Well Barrier in Tubing with Damaged Nipple Profiles

Isolation of failed inflow valve at high deviation

 

Technical Objective:

Isolation of failed inflow valve at high deviation.

Location:

Offshore, Brunei.

Customer:

National oil company.

Well Type:

Gas, 4 1/2-in to 3 1/2-in casing sizes, high deviation (69 degrees). 

Products/Services:

3 1/2-in SIM retrievable bridge plug and SIM running tool.

The Challenge:

With a failed downhole surface controlled formation isolation valve, a South East Asian customer recently installed retrievable bridge plugs to isolate a producing zone, to enable them to evaluate the performance of the reservoir. The challenge was compounded due to the high angle of well deviation and only having mechanical slickline available at the well site.

The Peak SIM plug was specifically selected by the customer for this challenge, given the low setting forces of the SIM plug and their experiences of deploying them by mechanical slickline in their highly deviated wells.

Considerations:

Three third-party formation isolation valves had previously failed and could not be used as a means of isolating the producing sands. The deeper deviated section of the well had also proved problematic in earlier well intervention operations, where the tubing crossover from 4 1/2-in to 3 1/2-in tubing was located.

Peak’s Solution:

On preliminary runs into the well, there were problems passing through the tubing crossover and the tools showed evidence of debris in the well. Several brush and gauge cutter runs were then made to clear any debris from the low side and to allow easier passage of tools to the target depth.

For the final SIM plug drift run, a Peak jar action indicator tool was incorporated above the SIM running tool to determine if sufficient jar action could be obtained downhole to set Peak’s 3 1/2-in SIM plug at target depth.

The initial drift run proved that it was possible to reach target depth and the jar action indicator tool gave the operator an indication at surface of how effective the jar action was.

Value to Customer:

This deployment highlighted the flexible nature of Peak's SIM plug and the fact it could be set at 69 degrees deviation, given the correct toolstring configuration, which was critical for successful deployment

  • Two 3 1/2-in SIM plugs were set, one just below the failed formation isolation valve valve and one just above. These two SIM plugs allowed isolation of the producing sand. The upper SIM plug was fitted with a downhole shut-in tool which allowed the sand to flow for a given period before the shut-in tool would close remotely, allowing a pressure buildup survey to be conducted
  • The customer was able to determine the flow characteristics of the sand and determine if it was worth future stimulation
  • The use of the jar action indicator tool allowed the slickline operator to determine the performance of downward jarring at depth in this highly deviated well. This in turn allowed changes to be made to both the running toolstring and SIM plug, to best meet the technical difficulties of setting a SIM plug at 69 degrees on slickline.

 

Product Code(s): SIM Retrievable Bridge Plug - 351, SIM Running Tool - 350